SRS wiring, wiring harnesses and connectorsħ.Safety belts, safety belt buckles and safety belt retractors.Instrument panel knee bolsters and mounting points.Steering column (deployable column if equipped).Inspect the entire vehicle for damage, including the following components: New driver and/or front passenger safety belt systems (including retractors, buckles and height adjusters) must be installed if the vehicle is involved in a collision that results in deployment of the driver and/or front passenger safety belt pretensioners.Ħ. When the driver air bag module has deployed, a new clockspring must be installed.ĥ. When any damage to the impact sensor mounting points or mounting hardware has occurred, repair or install new mounting points and mounting hardware as needed.Ĥ. If installation of an OCS system component is required, an OCS system service kit must be installed.ģ. For bladder-type OCS systems, inspect for damage and repair as necessary.Do not install a new OCSM unless DTC B1650 cannot be cleared. DTC must be cleared from the OCSM before carrying out Occupant Classification Sensor (OCS) System Reset. Install a new seat track with OCS system weight sensor bolts. For weight sensor bolt-type OCS systems, inspect the passenger side floorpan for damage and repair as necessary.For rail-type OCS systems, inspect the passenger side floorpan for damage and repair as necessary.When a vehicle has been involved in a collision and the Occupant Classification System Module (OCSM) has DTC B1650 stored in memory, the repair of the OCS system is to include the following procedures for the specified system: Refer to the appropriate workshop manual for OCS system removal and installation procedure. NOTE: After installation of new Occupant Classification Sensor (OCS) components, carry out the Occupant Classification Sensor (OCS) System Reset procedure as instructed in the workshop manual. Vehicles with Occupant Classification Sensor (OCS) systemĢ. DTCs must be cleared from all required modules after repairs are carried out. When any deployable device or combination of devices have deployed and/or the airbag control module (ACM/RCM) has DTC B1650 in memory, the repair of the vehicle SRS is to include the removal of all deployed devices and the installation of new deployable devices, the removal and installation of new impact sensors and the removal and installation of a new ACM/RCM. NOTE: Refer to the correct removal and installation procedure for all SRS components being installed. NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.ġ. NOTE: Always refer to the appropriate workshop manual procedures prior to carrying out vehicle repairs affecting the SRS and safety belt system. NOTE: Deployable devices (such as air bag modules, pretensioners) may deploy alone or in various combinations depending on the impact event. NOTE: After diagnosing or repairing a Supplemental Restraint System (SRS), the restraint system diagnostic tools (if required) must be removed before operating the vehicle over the road. Failure to follow this instruction may result in serious personal injury or death in a crash and possibly violate vehicle safety standards. If tools are not removed, the supplemental restraint system (SRS) device may not deploy in a crash. WARNING: Remove restraint system diagnostic tools from the vehicle prior to road testing. Inspection and Repair After a Supplemental Restraint System (SRS) Deployment No additional programming needed, when original module reset and put back in same vehicle. Send your airbag control unit to MyAirbags to have it reset.If you purchase a new or used module, it may require additional programming to your vehicle VIN Replace airbag control unit (new or used). Start Your Airbag Module Reset Order Today! How to fix/clear this code? It will give you the error "cannot execute routine". This code will not clear and won't erase with any diagnostic scan tool. Vehicle was in an accident and it has crash data stored in the SRSCM airbag control module. If you get a code B1650 Crash Recorded in 1st Stage Only Frontal, this means the How to fix KIA Hyundai SRSCM Airbag Code B1650 Crash Recorded in 1st Stage Only Frontal
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |